Reel box with ribbon and foamiran

Scotch tape is over, an empty solid reel remains, you should not throw it away! It can make a great box for storing jewelry or other important details. For example, you can create just such a bright striped casket!
 Box of reels
To make such a box you will need: - foamiran (plastic suede) green. - scissors . - bright yellow satin ribbon. - cabochon. - braid with carved sides. - rhinestones. - lighter. - a small piece of cardboard.
- ruler. - pencil. - clerical knife. - polymer glue. Making a casket. From the outside of a spool you need to remove scrape all remnants of scotch, leaving only the cardboard base.
 Box of reels
Having retreated from the edge of 1.3 cm, it is necessary to make an incision in order to obtain two parts of different sizes.It is important to ensure that the reel is cut evenly and is not crooked, so that the box will be even and beautiful. The greater part will be the casket, from the second, the small one will be made the lid.
 Box of reels
The lid on the box should hold tight and not loose, so you need to make a groove for it. A piece of thick cardboard should be cut out of a rectangular piece with sides of 23.5x5 cm.
 Box of reels
A strip of cardboard should be connected into a ring and completely pasted over with bright color tape. Particular attention should be paid to the inside of the rounded part, as it will be inside the box.  Box of reels
The prepared part should be greased with polymer glue on its outer side, not reaching the top edge 1.5 cm. After applying the adhesive, the blank must be folded into the frame of the future box, prepared from a reel of adhesive tape. A detail pasted with a ribbon will protrude by 1 cm, this is necessary for the lid of the casket, its tight closure.
 Casket from the reel
Now you need to make a bottom for the lid and the casket.For this, two large circles, 8 cm in diameter, must be prepared from thick cardboard.  Box of reels Every detail on one side needs to be glued with bright tape, after having pre-coated the surface with an even layer of glue.
Casket of bobbins
Now, from the green foyamiran, cut two circles with a diameter of 11 cm. The resulting circles should be glued to the blanks for the casket bottoms. The cardboard parts should be placed with the side with the ribbons up.
 Casket from a reel
Then, on the projecting edges of the foyaman, it is necessary to create a set of notches reaching the cardboard parts to ensure the convenience of further processing.
Box of reels
The frame for the lid of the casket on the inside should be covered with a satin ribbon, using polymer glue. Then the blank for the cover needs to be glued to one of the bottoms, gently brushing the edges of the cardboard circle with glue.
 Box of reels
The box frame also needs to be attached to the prepared bottom,immediately making cuts on the free allowance of green suede.
 Casket from the reel
Next, all admission foyamin should be glued to the sides of the casket and the lid for it. Bend carefully, avoiding creases and creating sharp corners.
 Box of reels
Now you should cut a 4.5x24 cm strip from the foamiran. The resulting blank should be attached along the entire side of the box , beforehand having greased it with polymeric glue. During attachment, it is important to ensure that there are no bubbles and voids below the material, to avoid deformation of the fabric after the adhesive has dried.  Casket from a reel Then from Foamiran you will need a thin strip for the cover . Its dimensions should be 1.5x24 cm. It should be fastened with a polymer adhesive applied evenly over the outer side surface of the lid. Casket from a reel It turns out that such a casket, it remains to decorate her prepared rhinestones,half-buffets and braid. Box of reels On the side of the lid, you should attach a silver lace tracery. Its width should not exceed 2 cm so that it does not strongly protrude beyond the edges of the lid.
 Casket from a reel
From the same braid you need to make a strip on the bottom of the casket, to connect the composition with the lid .
Casket from bobbin
Now you need to make a decoration for the cover of the casket. As a basis, you need a square from the fameiran, not less than 4x4 cm. -shkatulka-iz-bobiny.jpg "alt =" Box of reels "title =" Box of reels "> On the center of the base you should glue the cabochon.
 Casket from a reel
Around the cabochon is to attach a row of half-beads, tightly applying, to each other.
 Casket from the reel
In the second row, semi-beads should be attached to the spacing details of the first circle.
 Casket from a reel
Excess material should be cut off, leaving only a flower from half-beads .The cut of foamiran needs to be slightly scorched, to give a finished look.
 Box of reels
This flower should be attached in the center of the lid.
 Box of reels
It remains to supplement the cover surface with several rhinestones, forming a circle out of them.
 Box of bobbins
T pens should be added to the side of the box with the same rhinestones, attaching them at equal distance.
 Box of reels
It turns out such a bright box of simple materials and an empty reel of Scotch tape.
Box of reels
The casket is ready, you can put into it any little thing!

Related News


Kate Winslet believes that the curvy form is now in vogue
The couple bought a mini-apartment of 28 sq. M. The architectural bureau created a small miracle, the transformation was radical
Construction mesh, hoop and cardboard instead of a loom
Infectious diseases in the period of newborns
What is dangerous lack of calcium for the body?